The LAN8650/1 combines a Media Access Controller (MAC) and an Ethernet PHY to enable low‑cost microcontrollers, including those without an onboard MAC, to access 10BASE‑T1S networks. The common standard Serial Peripheral Interface (SPI) of the LAN8650/1 allows interfacing with nearly any microcontroller, so that the transfer of Ethernet packets and LAN8650/1 control/status commands are performed over a single, serial interface. SPI also requires only 4 pins, enabling a simpler hardware interface with fewer pins than MII or RMII.

Ethernet packets are segmented and transferred over the serial interface according to the OPEN Alliance 10BASE‑T1x MAC‑PHY Serial Interface specification. The serial interface protocol can simultaneously transfer both transmit and receive packets between the station controller and the LAN8650/1. Packets are typically stored within the LAN8650/1 before being forwarded to either the station microcontroller or to the network. Alternatively, packets may be transferred in a cut-through mode for applications needing reduced latency.

• 8x 1G Copper Ports.
• External DPLL for <1ns system PTP time synchronization with exposed connectors for system synchronization.
• PCIe and expansion headers for rapid prototyping, software development and system integration.

The EVB-LAN9668 is the evaluation board for the LAN9668 TSN Switch. The EVB-LAN9668 implements 8 Gigabit Ethernet ports with the LAN9668 Switch and LAN8814 PHYs.

The SAMA7G54-EK evaluation kit is intended for evaluating and prototyping with the SAMA7G54 microprocessor. The SAMA7G54 is a high-performance, ultra-low power Arm Cortex-A7 based embedded microprocessor (MPU) running up to 1GHz. It supports multiple memories such as 16-bit DDR2, DDR3, DDR3L, LPDDR2, LPDDR3, octal/quad SPI and e.MMC Flash. The SAMA7G54 integrates complete imaging and audio subsystems with 12-bit parallel and/or MIPI-CSI2 camera interfaces up to 8 Mp and 720p @ 60 fps, up to four I2S, one SPDIF transmitter and receiver and a 4-stereo channel audio sample rate converter. The device also features a large number of connectivity options with Dual Ethernet (one Gigabit ethernet and one 10/100 Ethernet), six CAN-FD and three high-speed USB and offers advanced security functions such as: secure boot, secure key storage, high-performance crypto accelerators for AES, SHA, RSA and ECC.

The SAMA7G54-EK board itself features connectors and expansion headers for easy customization and quick access to leading edge embedded features such as Mikroelektronica click boards and Raspberry Pi expansion header plus MIPI CSI camera. The kit is supported by mainline Linux distribution as well as bare metal software frameworks and RTOS allowing you to easily get started with your development. The kit includes an on-board Embedded Debugger, eliminating the need for external tools to program or debug.

You can use high-voltage auxiliary E-Fuse technology in Hybrid Electric Vehicle (HEV) and Electric Vehicle (EV) applications. This technology demonstrator leverages the benefits of our 700V and 1200V Silicon Carbide mSiC™ products to provide a complete solution. This design also implements a Time-Current Characteristic (TCC) curve that helps you migrate to non-automotive applications such as DC solid-state circuit breakers.

• Configurable current limit profile
• LIN communication interface for configurability and diagnostics
• High-side or low-side drive configuration
• Short-circuit withstand time: 10 µs
• Rated current: 30A
• Low-voltage operating range: 9V to 16V
• High-voltage operating range: 200V to 900V
• Operating temperature range: −40°C to 85°C
• Automotive hardware design that uses only AEC-qualified components
• Six variants of this high-voltage auxiliary E-Fuse design that support 400V and 800V bus voltages and continuous current ratings of 10A, 20A and 30A
• Up to 20 kHz switching frequency

The PolarFire® SoC Video kit is the Industry’s first RISC V SoC FPGA- based, full-featured embedded vision development platform targeting secure, reliable, and power-efficient vision applications at the edge, including Microchip’s VectorBlox Accelerator SDK and Neural Network IP, and Industrial IoT and Automation.

The kit supports dual 4K MIPI CSI-2 cameras, HDMI 2.0 with FMC-based expansion towards CoaXPress 2.0, 6/12G SDI, 1/ 2.5/ 5/ 10G USXGMII, and USB 3.1 Gen1 and Gen2 protocols. It also includes USB 2.0, SD Card, eMMC, PCIe Gen2x4 endpoint or root port, and a MikroBus connector facilitate Microchip’s Trust & Go platform for cloud connectivity.